lutron homeworks sunnata dimmer

HOMEWORKS HRST-PRO-N Sunnata LED+ RF Dimmer Instruction Manual

Table of Contents

HOMEWORKS HRST-PRO-N Sunnata LED+ RF Dimmer

Turn power off at circuit breaker, load types and operation, determine wiring configuration, troubleshooting, fcc / ic / ift information, read user manual online (pdf format), download this manual (pdf format).

How-to videos

Find the right LED Help

Use our mobile friendly self-paced installation tool: www.lutron.com/wiringwizard Find more product information: www.lutron.com/support

• Frequently Asked Questions
• Online Chat (8 am – 5 pm EST)

Call us: U.S.A. | Canada | Caribbean 1.844.LUTRON1 (588.7661) (24/7) Mexico +1.888.235.2910 Others +1.610.282.3800

www.lutron.com/support

Limited Warranty: www.lutron.com/TechnicalDocumentLibrary/Warranty.pdf For FCC/IC information: Please visit: www.lutron.com/fcc-ic )Lutron, Lutron, Sunnata, Claro, FASS, LED+, Pico, HomeWorks, and Satin Colors are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries. App Store is a service mark of Apple Inc., registered in the U.S. and other countries. All product names, logos, and brands are property of their respective owners.

WARNING: ELECTRIC SHOCK HAZARD . May result in Serious Injury or Death. Turn off power at circuit breaker or fuse before installing

| Minimum Load| Maximum Load| __

| Required Phase Mode 1 ---|---|---|---|--- Single Gang| End of Gang| Middle of Gang LED| 1 bulb| 250 W| 200 W| 150 W| Required| Either MLV

Transformer with LEDs

See Application Note #559 (P/N 048559) at www.lutron.com

Transformer with Halogen

No Derating Required

Incandescent /

| 10 W| 500 W| 400 W| 300 W| Required| Either Dimmable Fluorescent

| 3.3 A (400 VA)| __

Hi-lume 1% 2-wire

| 3.3 A (400 W) 20 drivers

PHPM-PA / 3F

and GRX-TVI

| 1 interface| 3 interfaces| No Derating Required| Required| Forward CFL| 1 bulb| 250 W| 200 W| 150 W| Required| Forward

1 See Section 7 on page 2 of this guide for phase-select instructions.

Note: For dimming MLV fixtures, the maximum lamp wattage is typically 70%-85% of the transformer’s VA rating. For actual transformer efficiency, contact the manufacturer. The total VA rating of the transformer(s) shall not exceed the VA rating of the dimmer.

• CAUTION: Use only with permanently installed fixtures with dimmable screw-in LED, dimmable self-ballasted compact fluorescent, halogen, or incandescent lamps. Use only to control the primary side of permanently installed transformer supplied low-voltage lighting, or in combination with incandescent lamps. To reduce the risk of overheating and possible damage to other equipment DO NOT use to control receptacles, fluorescent lighting fixtures, non-ballasted or externally ballasted compact fluorescent lamps, motor operated appliances or transformer supplied appliances.
• Neutral is required for all load types.
• Install in accordance with all national and local electrical codes.
•  When no “grounding means” exist within the wallbox, the NEC® 2011, Article 404.9 allows a dimmer without a grounding connection to be installed as a replacement, as long as a plastic, noncombustible wallplate is used. For this type of installation, twist a wire connector onto the green ground wire or remove the green ground wire on the dimmer and use an ap pro pri ate wallplate such as Claro or Satin Colors series wallplates by Lutron.
• Protect the dimmer from dust and dirt when painting or spackling the wall.
• This dimmer is not compatible with standard 3-way or 4-way switches. Use only with Lutron companion dimmers listed above.
• In any 3-way / 4-way circuit use only one dimmer with up to 4 companion dimmers.
• Maximum wire length between the dimmer and the farthest companion dimmer is 150 ft (45 m).
• Operate between 32 °F and 104 °F (0 °C and 40 °C).
• It is normal for the dimmers to feel warm to the touch during operation.
• Clean the dimmer with a soft damp cloth only. Do not use any chemical cleaners. For disinfecting, please refer to App Note #758 (048758), “Cleaning Recommendations for Lutron Products” at www.lutron.com.
• For indoor use only.

Fully wrap the wires around the screw and tighten (A), or strip insulated wires to 1/2 in (13 mm) and insert into the push-in terminals (B). Solid copper wire only.

Mount all devices using the provided screws and attach wallplate Turn power ON at circuit breaker

Setup for use WITHOUT a system NOTE: If setting up as part of system, phase settings and low-end trim levels made on the dimmer will be over-written by the system software.

Adjust Low-End Trim

• Press and hold middle (LED 5) of light bar until dimmer goes to low-end and low-end setting starts to flash.
• Slide up or down on the light bar.
• Press and release Off to save and exit.

Phase-Select Mode

Pull out the Front Accessible Service Switch (FASS).

 Press and hold On . Push in the Front Accessible Service Switch (FASS) and continue to hold On LED 1 and LED 9 start flashing. LED 9 – Forward-Phase LED 1 – Reverse-Phase (default)

Release the On . LED 1 or LED 9 will be flashing to indicate current phase mode

Press and hold On to save and exit.

See the Sunnata MyLevel Personalization Application Note #734 (P/N 048734) at www.lutron.com/HWsupport for details on how to change these settings.

Setup for use WITH a system

NOTE: If setting up as part of system, phase settings and low-end trim levels made on the dimmer will be over-written by the system software. For use in a HomeWorks system, please refer to the Getting Started Guide: www.lutron.com/HWsupport For reliable performance in a system, this device should be placed within 25 ft (7.6 m) of two additional compatible HomeWorks Sunnata dimmer, switch, keypad or HomeWorks processor wireless devices. For more information please refer to the Wireless Setup guide: www.lutron.com/HWsupport

Lutron’s led compatibility tool at www.lutron.com/ledfinder The phase is not set to the correct setting for your load type| 1.  Confirm Phase Setting for your load type. See Table in Step 2

2.  Change Phase Select Mode in Step 7

The low-end is not adjusted| Perform low-end trim adjustment in Step 7 LED lights do not dim low enough| The low-end is not adjusted| Perform low-end trim adjustment in Step 7 LEDs 1, 7 and 9 are flashing (Hot-Dimmed Wire Miswire)| Wiring error. Product may be permanently damaged| Check wiring to be sure it matches installation instructions and wiring diagrams LEDs 7, 8 and 9 are flashing (Blue Screw Miswire)| Wiring error. Product may be permanently damaged| Check wiring to be sure it matches installation instructions and wiring diagrams LEDs 1 and 7 are flashing (Over Voltage Protection)| The phase is not set to the correct setting for your load type| 1.  Confirm Phase Setting for your load type. See Table in Step 2

Bottom three LEDs 1, 2, and 3 are flashing (Shorted FET Detection)| Wiring error. Product may be permanently damaged| Check wiring to be sure it matches installation instructions and wiring diagrams Middle LED 5 is flashing (Over Temperature)| Load may exceed maximum load rating| Ensure load does not exceed the maximum allowable load. See Table in Step 2 Ambient temperature may exceed maximum product rating| Turn unit off until the ambient temperature returns to the normal operating range Unit needs to be reset| Cycle power to the unit using the Front Accessible Service Switch (FASS) to reset All LEDs are flashing (Over Current Protection)| The phase is not set to the correct setting for your load type| 1.  Confirm Phase Setting for your load type. See Table in Step 2

Bulbs may have failed| Verify that no bulbs have failed Wiring error. Product may be permanently damaged| Check wiring to be sure it matches installation instructions and wiring diagrams The dimmer may need to be reset| Cycle power to the unit using the Front Accessible Service Switch (FASS) to reset The lamp is not compatible with your Lutron dimmer| Find a compatible lamp by visiting Lutron’s led compatibility tool at www.lutron.com/ledfinder Load is OFF and there is no LED lit on the dimmer| Power Not Present

Circuit breaker OFF or tripped Load is not installed or connected

Front Accessible Service Switch (FASS) is in the OFF position

Ensure breaker is On

Dimmer must have a load to operate.

Move Front Accessible Service Switch (FASS) to the ON position by pushing it in

Wiring Error

Product is not wired correctly

Check wiring to be sure it matches installation instructions and wiring diagrams

Light turns ON and OFF continuously| Improper load type or less than the required minimum load| Recommended minimum load is 10 W/ 10 VA or one compatible LED lamp listed at www.lutron.com/ledfinder Dimmer LED is ON but load cannot be turned on or off| Wiring error| Check wiring to be sure it matches installation instructions and wiring diagrams Lamps failed or not installed| Replace or install lamp Lights don’t turn ON/OFF from a keypad or from other remote device| Improper programming| Refer to the HomeWorks software or Lutron App to ensure proper programming Out of RF range| Reposition to be within 25 ft (7.6 m) of an RF signal repeater or another RF device

This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

• This device may not cause interference, and
• This device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user’s authority to operate this equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment. The user should avoid prolonged exposure within 7.9 in (20 cm) of the antenna, which may exceed FCC/ISED radio frequency exposure limits. This Class B digital apparatus complies with Canadian ICES-003.
• Lutron Support Center
• LED Compatibility Tool | Lutron
• Lutron: Beautiful light. Intelligent Shades. Powerful Controls
• lutron.com/fcc-ic
• Lutron Support Center | Lutron
• How to Install a Dimmer Switch | Dimmer Switch Wiring | Lutron Web Tools

Download this manual  >>

HOMEWORKS User Manuals

Related manuals.

• United States
• Middle East
• Latin America
• Register or Login to myLutron
• Where to Buy

Lutron Product Delivery Lead Time Update

Lutron Lead times are improving rapidly.

Discover Lutron Luxury

Connected lighting, shades, and hand-crafted controls that elevate everyday life.

Specification Guides

The Specification Guides provide detailed product information to help you specify the right Lutron solution for your project.

New Lutron Support Center

Product specific FAQs Product specific troubleshooting Help finding the correct product Popular tools and resources Request color samples

Lighting Control Institute

Want to learn about installing or programming Lutron solutions? Looking for best practices for selling or specifying? LCI offers online training and in-person workshops for industry professionals.

LED Control Center of Excellence

Visit our Control Center of Excellence for tools and resources to help you select, install, and use LEDs with confidence. Designed for homeowners and industry professionals.

HomeWorks QS Maestro Dimmers & Switches

Colors & finishes.

• Serena Shades Store
• Related Sites
• Online Training (LCI)
• myOrders Login
• eMaps Login
• Customer Support
• Online Support Center
• Lutron Support Community
• Customer Assistance
• International Support & Contact
• Provide Site Feedback
• Important Safety Notice(1)
• © 2024 Lutron Electronics Co., Inc
• Privacy Policy
• Cookie Preferences
• Do Not Sell My Personal Information
• Trademark Guidelines
• Anti-Slavery & Human Trafficking Statements
• Transparency in Medical Coverage

How can we help you today?

Product Selection

FAQs Documents

Troubleshooting

Popular Topics

• Cleaning Recommendations for Lutron Products
• Help wiring your dimmer
• All your 0-10V questions answered
• Find the correct LED bulb or LED Dimmer

Looking for help? We've got you covered

Explore knowledge articles.

LED Compatibility

System Design & Setup

Troubleshooting

Programming

Sunnata PRO Dimmers & Switches for RadioRA 3 System

Model numbers.

• RRST-PRO-N-__ (Color)  DIMMER
• RRST-8ANS-__ (Color)  SWITCH

Knowledge Article Contents:

Section (1):  verifying your application.

Section (2):  RadioRA 3 Sunnata PRO Dimmer & Switch Specifications 

Section (3):  product installation, notes on installation, radiora 3 sunnata dimmers and switches require a neutral connection, radiora 3 sunnata dimmers and switches must be required on the load side.  , section (4):  troubleshooting  , fass switch.

Would you like to provide additional feedback? Yes No

Choose how you would like to see content specific to your location.

• Make this my default

Welcome to the Lutron Luxury Portfolio

Designer Spotlights

Consult with a trained specialist to learn which solutions fit your design.

Sunnata Switches

Product Specification

• Sunnata RF Dimmers / Switch - Product Specifications

Installation Guides

• Sunnata RF Switch - Installation Guide

Design Files

• Specification Tools
• Bluebeam/CAD Tool Kit
• Application Notes
• Application Note #793 - Sunnata Switch MyLevel Personalization

Caséta Support

Looking for help we've got you covered, explore knowledge articles.

Bridge Connection

Connected Products

Product Installation

Product Selection

Troubleshooting

Using the App

Flickering / Flashing LED Lights with Caseta Dimmers

Dimming leds:  common problems and how to work through them, what causes led bulb flicker or flashing, what can you do about it.

• Make sure your Lutron Dimmer and LED bulb(s) are compatible. There are not any manufacturing standards for LEDs, which means they differ from bulb to bulb.  Even though a bulb may say that it is dimmable, some will dim down further and smoother than others.  Some bulbs perform best only when working with a specific type of dimmer.  This can make choosing the right dimmer and compatible bulbs difficult. Lutron is one manufacturer that tests the latest LED bulbs and posts the ones that we have found to work best.  To view Lutron's list of compatible dimmers and tested bulbs, visit the Lutron LED Compatibility Tool .
• Adjust your dimmer's low-end trim Flicker is often more prevalent at lower light levels.  The low end on your Caseta dimmers can be adjusted to reduce low-end flicker by following the directions below or watching this Video .

• Use a dimmer with a neutral wire

• Change out one bulb for an incandescent/halogen Because this is not ideal, this is the last resort.  If you do not want to change all of your LED lamps, then you can insert an incandescent / halogen bulb into the circuit.  This can help to stabilize the other LED lamps and improve the dimming performance. To learn more about common problems with dimming LEDs, please visit Lutron's LED troubleshooting page

Would you like to provide additional feedback? Yes No

Lutron Homeworks Sunnata Keypad

Intuitive keypads make lighting control simple Lutron launches homeworks qs whole house control Lutron keypads accessories ravepubs

Keypad lutron keypads intuitive surprisingly brushed raise hwis Lutron homeworks qs Lutron homeworks qs whole

Lutron keypad brochure qs homeworks keypads architrave brilliantlighting

Lutron keypads automation instagram lighting choose board smart#lutron #keypads #designmeetstech Lutron keypads keypadLutron keypad radiora hybrid lighting overview switch dimmer control light wall dimming led system single.

Lutron extends its family of keypads, dimmers and accessories – rave [pubs]Lutron keypad radiora keypads ra2 switches .

#Lutron #keypads #designmeetstech | Smart home design, Lutron, Home

Lutron Extends its Family of Keypads, Dimmers and Accessories – rAVe [PUBS]

lutron-keypad - Soundworks Inc

Intuitive keypads make lighting control simple | Brilliant Lighting

Lutron HomeWorks QS | Brilliant Lighting

More Posts:

• ›   Raspberry Pi 4 Schematic
• ›   Lutron Fan Switch Install
• ›   Lutron 3 Way Light Switch
• ›   Mercruiser 3.0 Fuel Pump Diagram
• ›   Positive Negative Dc Barrel Jack Wiring
• ›   Origin Windows 11
• ›   Maaco Auto Near Me
• ›   Natick Gas Auto Repair
• ›   Plant Cell Diagram Unlabelled

• Whole Home Solutions
• Color, Style, & Fabrics
• Residential Applications
• Right Environment
• Human Centric Lighting
• Tunable White & Color Control
• Smart Buildings
• Color, Style & Fabrics
• Service Overview
• Market Segments Market Segments
• Case Studies

Dimmers & Switches

• Fan Controls
• In-wall Sensors
• LED+ Dimmers
• Wallplates & Accessories
• Code Smart Guestroom System
• Contract Roller
• Hyperion Solar-adaptive Shading
• Ketra Lighting
• Finiré Downlights
• Lumaris Tape Light
• LED Upgrades
• Vive Fixture Control
• Service Offerings
• Replacement & Upgrade
• Service FAQs
• Technical Documentation & Support Overview
• Specification Guides
• Product Specification Submittals
• Performance Specifications
• Installation Instructions
• Wiring Diagrams
• CAD Downloads
• Revit Downloads
• Engraving Sheets
• Product Customization Forms
• UL Conditions of Acceptability
• Technical Papers
• Application Notes
• Technical Reference Guides
• Design & Configuration Software
• Product Selection Tools
• User Guides & Videos
• Technical FAQs
• Legacy Products
• Customer Support
• Serena Shades
• Not Sure Who to Contact?
• Dimming Basics
• How to install a dimmer
• Quick & Easy Troubleshooting
• What is Light Control?
• Energy Efficiency
• LED Center of Excellence
• Technologies
• Glossary of Terms
• Codes & Standards, US & Canada
• Commercial Application Guides
• Energy Saving Strategies
• Energy Benchmarking
• Continuing Education (CEU)
• North America Locations
• Lutron Worldwide
• The Lutron Experience Center
• Media & Press Center
• International Contact Information
• Provide Site Feedback
• Register or Login to myLutron
• United States | English (US)
• Where to Buy

How can we help you today?

Product Selection

FAQs Documents

Troubleshooting

Popular Topics

• Cleaning Recommendations for Lutron Products
• Help wiring your dimmer
• All your 0-10V questions answered
• Find the correct LED bulb or LED Dimmer

Lutron offers hundreds of choices in stand-alone dimmers and switches. With a wide array of styles, colors and control options we can complement any décor and provide functionality for ambience, convenience, and security-meeting all of your lighting control needs.

Need help or have a question? Our new Support Center can easily help you out.

Explore our Dimmer Styles